Swim'n Play ABOVE GROUND SWIMMING POOL User Manual

OVALPOOL ASSEMBLY INSTRUCTIONSPart# 420364-14313 REGINA AVENUE, RAHWAY, NEW JERSEY 07065-4891Phone: (732) 574-1500 • Fax: (732) 574-1551 • www.swimnpl

10BOTTOM RAIL AND STRAP LAYOUT4Follow the instructions below to properly layout the rail and strap assemblies.QUANTITIES NEEDED:POOL SIZE 16 x 10 18 x

Remove wall from carton. NOTE: the UP arrow on wall.Determine starting point as thefilter inlet and outlet holes are atthe beginning of the wall. St

12PROTECT YOUR LINER7Once the wall is closed andscrews and nuts are tightenedsecurely, cover the screw heads on the inside of the pool with acloth tap

13HOLD DOWN SHEET10The hold-down sheets are inserted lip down into the bottom rail inside the pool as shown.Do not bend the hold-down sheet out of sha

14THRU-THE-WALL SKIMMER11IMPORTANT!! BEFORE CONTINUING WITH THIS STEPYOU MUST KNOW WHICH TYPE OF THROUGH THE WALL SKIMMERYOU WILL BE USING WITH YOUR

Wall guard is optional.Tape wall guard (plastic sheeting) to pool wall 12" up fromground and smooth out on ground 12" from wall. This will

CAUTIONYOUR POOL IS DESIGNED TO PROVIDE AN AMPLE SAFETY MARGINWHEN IT STANDS ON LEVEL GROUND. FOR THIS PURPOSE A SLOPE IN EXCESS OF 2 INCHES IN ANY D

17EZ HOOK LINER INSTALLATIONATTENTION: An 8 inch cove must be placed all around the inside of the pool1. Clear all sticks and sharp objects from an ar

18VERTICALS, TOP PLATES AND RAILS15PRE-ASSEMBLY OF TOP PLATES*14No. 12 x 1/2”Sheet MetalScrewIf fencing or decking is to be installed, refer to the de

19No. 12 x 1/2”Sheet MetalScrewInsert two rails into a plate, in the same manner and using the same spacing as you have done on the bottom rail and pl

2CONTRACT INSTALLATIONSThe manufacturer is in no way affiliated with any professional pool installer. Therefore the manufacturer can assume norespons

Your pool is equipped with (3) three special warning ledges. The (1) one ledge witha large warning on top is to be installed by the entry point into

21INSTALLING TOP COVERS17FOLLOW THE INSTRUCTIONS BELOW FOR THE COVERS FOR YOUR PARTICULAR POOL4", 6" & 7" DELUXE TOP COVERSThese co

226" & 7" TWO-PIECE FULL CONTOURED COVERSlide inside cover (the cover which will be closest to the inside of the pool) into position and

237" AND 9” TWO-PIECE WRAP AROUND COVER AND PEDESTALSlide the inside cover (the cover which will be closest to the inside of the pool) into posit

24Educational programs and materials, (i.e. seminars, workshops, brochures, videos, instructional guides, etc.) areavailable from NSPI, NSPF, other aq

25SAFETY TIPS - RULES AND REGULATIONSThis section is designed to acquaint you with some guidelines as to the safe operation and use of your pool.• Do

26WARNINGCheck all the metal on the pool frame and pool wall for signs of corrosion or deterioration. Remove any corrosion and touch up with paint.

A reliable pool water test kit will help to determine the daily chlorine dosage and the acid-alkaline condition of thewater. You will find in the tes

28313 REGINA AVENUERAHWAY, NEW JERSEY 07065-4891Phone: (732) 574-1500 • Fax: (732) 574-1551E-mail: [email protected]

3SOME FRIENDSTO HELP OUTHammerKnifeTapeRake4” NailPliersCloth TapeCenter Stake2 x 4Sifted Earth or Pre Washed SandBroomPatio BlocksCarpentersLevelShov

4INSTALLATION • ASSEMBLY STEPSREAD CAREFULLY BEFORE STARTING POOL ASSEMBLYCONSTRUCTION CLOSE-UPSUse the illustrations below as a guide for the assembl

5INSTALLATION • ASSEMBLY STEPSREAD CAREFULLY BEFORE STARTING POOL ASSEMBLYCONSTRUCTION CLOSE-UPSUse the illustrations below as a guide for the assembl

6INSTALLATION • ASSEMBLY STEPSREAD CAREFULLY BEFORE STARTING POOL ASSEMBLYCONSTRUCTION CLOSE-UPSUse the illustrations below as a guide for the assembl

POOL SIZE DISTANCE: DISTANCE: DISTANCE: DISTANCE: DISTANCE: DISTANCE: DISTANCE:A TO A A TO B B TO B B TO C A TO C C TO C X V W Z D to D(Pool Length) (

Using the “CLEARANCE SIZE” chart on page 6, determine the clearance size for your pool.With the use of the leveling device shown and a shovel start le

9ASSEMBLING THE BOTTOM STRAPS3Unpack and assemble the bottom straps with the buttress bottom plates and brackets as shownusing all necessary hardware